Editors of Popular Woodworking - Joinery tips & techniques : how to cut perfect wood joints every time

There are three basic saw cuts: crosscuts, rips and miters. Crosscuts are made perpendicular to the wood grain, rips are cut parallel to the grain and miters are made at angles diagonally across the grain. None of these requires elaborate jigs or complex techniques, but they are the building blocks to basic joinery on the table saw.

Rips and crosscuts are used to form many joints, including the basic edge and butt joints, which can be used to glue up a tabletop or door frame. These two cuts are also used to cut rabbets, grooves and dados. And a variation of these cuts will create a miter joint.

Miters can be the most frustrating cuts to make. Angled cuts are harder to measure and lay out than crosscuts. To make a mitered frame perfect, both the inside and outside dimension of the piece must match on each component. You should start with accurate measuring tools and some basic math, and then you will need to test and retest your setup to ensure its precision.

When you make a miter cut on a table saw, you run into a problem associated with crosscuts the factory-supplied miter gauge is too small to offer adequate support for guiding most boards. To properly support the work, you must fit the gauge with an extension fence or replace it with a sliding table.

Even when using an adequately sized miter gauge, boards are inclined to creep during a miter cut because of the rotation of the blade into the cut. One way to compensate for this is to add a stop to your miter gauge fence as shown above. Your stop will also help you make repeatable, accurate miter cuts every time.

To make sure your miters are perfect, start with a new zero-clearance throat insert on your table saw. Bring the blade up through the insert until the blade height is about above the height of your frame material. Turn off the saw. After the blade has stopped, use a straightedge to make a mark, extending the line of the blade slot the full length of the insert. This will let you see exactly where the blade will cut. Add a sacrificial fence to your miter gauge that extends past the blade to eliminate tear-out. You can also extend the cut line to the sacrificial fence for extra alignment accuracy.

Accurate angles are another problem on table saws. The stock miter gauge and blade-tilt scale on most table saws even the best ones are notoriously imprecise. And you cant use a drafting triangle to set every possible angle you might want to cut. You must use the scales to estimate the degree setting, then thoroughly test the setup until you have it right.

Once the miter gauge angle is properly set, make the miter cuts. If the boards are to be joined by miter joints (such as the members of a frame), you must make mirror-image miters. Note: A single miter joint is comprised of one left miter and one right miter. To do this, flip each board end-for-end, keeping the same edge against the gauge as you cut the ends. Only in rare instances when you cant flip the board should you have to readjust the angle of the miter gauge to cut left and right miters.

A simple stop clamped to your miter fence will keep your piece from slipping during the cut.

To create accurate, matching miters (or butt joints) for frame work, flip the work piece end-for-end keeping the same long edge against your miter gauge, as shown here.

You also can cut a miter by tilting the blade rather than angling the miter gauge. This procedure is similar, but there is an important difference when cutting left and right miters. As you rotate the board end for end, the same face must rest against the table. Note: You can switch faces if you first switch the miter gauge to the other slot.

The procedure to make a bevel is similar to the way you make a miter, but you must set the blade at the proper angle, rather than the miter gauge. Measure the angle between the blade and the table with a triangle or a protractor.

If you rip a bevel or chamfer, make sure the blade tilts away from the rip fence. This gives you more room to safely maneuver the board and reduces the risk of kickback. On right-tilt saws, you will have to move the rip fence to the left side of the blade (as you face the infeed side of the table saw).